[hibiscus_horz]

Basic Cisco configuration commands


1.      Connect PC Ethernet port and Cisco router Ethernet port  by using:
  • Cross-over UTP cable  (cable with pin 1 connected to pin 6 and pin 2 connected to pin 6, both on RJ45 connector) or by using:
  • HUB and two straight UTP cables.
2.      Power on the router and look at the massages appearing on the screen, while the router is booting

Part 1
BASIC COMMANDS
Using the commands on the router:
  • show version
  • show ip interface brief (or show interface)
Answer the following questions:
1. Router name:
2. Router type:
3. IOS version:
4. Memory amount:
5. Flash ROM amount:
6. Number and types of interfaces:
Part 2
              
Part 3
Set up a new  IP address, mask and Default Gateway  on each  WG PC
  • Each WG should decide which IP addresses will be used (from each subnet) for PC to router connection and for router to router connection . 
  • Start -> Settings -> Control panel -> Network -> TCP/IP Ethernet… -> Properties -> IP address and Gateway
Part 4
Displaying the configurations
      Enter privilege mode (enable)
     Display the configuration saved in NVRAM (show config)
     Display the running configuration (show running-config)
Setting and changing the configuration
      Enter the configuration mode (conf term)
     Change the router name (hostname)
     Exit the privilege mode (CTRL-Z), you are back in Privileged mode!
     Save the configuration (copy running-config startup-config)
Setting the passwords (REMEMBER YOUR PASSWORD)
      Enter the configuration mode (conf term)
     Specify virtual terminal lines you would like to configure (line vty 0 4)
     Request login authentication (login)
     Set a password for the exec mode (password my_password)
     Set a password for the privileged (enable secret my_password)
     Exit the privilege mode (CTRL-Z), you are back in Privileged mode!
Configuring the interface
     Enter the configuration mode (conf term)
     Select first ethernet interface 
     (interface ethernet – you got all the types of interfaces from part 1 task – for example Interface Ethernet0/0)
     Select the ip address and subnet mask (ip address your_IP_address  mask )
     Enable the interface (no shut)
     Exit the privilege mode (CTRL-Z), you are back in Privileged mode!
Checking router status and IP connectivity
      Check host connectivity (ping connected_PC_ip_address)
     Check host reachability (trace connected_PC_ip_address)
     Check status of an interface (show interface eth?)
     Display debug information (debug ip icmp)
     Disable debug information (undebug all)
Part 5
 Establishing router to router connectivity:
 Configuring the Serial interface:
  Enter the configuration mode (conf term)
     Select first Serial interface 
    (interface Serial – you got all the types of interfaces from part 1 task – for example Interface Serial0)
     Select the ip address and subnet mask (ip address your_IP_address  mask )
      Find out which Serial interface got connected DCE and which DTE CISCO cable
·        DTE (Data Terminal Equipment – MALE conector)
·        DCE (Data Communication Equipment – FEMALE connector)
      On Serial Interface with DCE cable enable line CLOCK by entering the command:
·        clock rate 1000000
      Enable the interface (no shut)
     Exit the privilege mode (CTRL-Z), you are back in Privileged mode!
  Connect DTE and DCE cable
  Checking router status and IP connectivity
      Check neighbor router connectivity (ping connected_router_ip_address)
     Check status of an interface (show interface serial?)
 Provide routers  with info where other (not directly connected) subnets  are by configuring static routes on each router:
 The command is:
 ip route
 ·         is the subnet used for router-to-PC connection on the neighbor router
or the subnet between next two routers
·         is IP address of  serial interface on the neighbor router
 Check  connectivity  (ping) from your PC to all other PC’s in your WG
·        open DOS window  (Start -> Programs -> DOS)
·        ping host_ip_address
 Check  reachibility (traceroute) from your PC to all other PS’s in your WG
·        open DOS window (Start -> Programs -> DOS)
·        tracert host_ip_address
Part 6  (optional)
 Connect your network to other WG network (by Ethernet or Serial connection):
·        decide which subnet will be used for interconnection
·        configure static routes to other subnets
·        Check  connectivity  (ping) from your PC to all other PC’s (in others WG)
·        Check  reachibility (traceroute) from your PC to all other PS’s (in others WG)


TOP